The official page for downloading firmware and utilities for recovery – https://www.asus.com/support
In order to reset the ASUS RT-N10 to its factory settings 1. Find the reset button on the rear of the router 2. Turn the device off and wait a few seconds. Hold the Reset button in with a pen and insert power. Wait until the WPS light blinks slowly and then let go of the Reset button. Your router is now in recovery mode and has the IP 192.168.1.1. The user-friendly ASUS RT-N10 150Mbps wireless router uses multiple SSIDs and the EZ user interface for three-step quick setup. No manual or install disc required – enjoy a stable network with ease. 6 RT-N10+ Chapter 1: Knowing your wireless router Knowing your 1 wireless router Package contents Check the following items in your ASUS Wireless Router package. RT-N10+ Wireless Router x1 Power adapter x1 RJ45 cable x1 Quick Start Guide x1 Note: If any of the items is damaged or missing, contact your retailer. System requirements. 1- Place the Asus RT-N10 in firmware upgrade mode; 2- Use Asus Firmware Restoration utility to upload the firmware; 3- After the upload is complete open your browser, go to the router by typing 192.168.1.1, when prompted for a username and password enter 'admin' for both.
Direct links:
https://www.asus.com/Networking/RTN10/HelpDesk_Download/
https://www.asus.com/Networking/RTN10_C1/HelpDesk_Download/
Asus Rt N10+ Reset Password
To update the firmware through the web interface, you need to open “Administration” – “Firmware Update”, select the new firmware file and click the “Submit” button. Wait until the operation is completed and in no case do not turn off the power of the router.
The new firmware must be necessarily under the version of the router, you can see it on the label under the router (for example, VER.B1, VER.С1, etc.). Flashing the wrong version can ruin the router.
On the test after flashing the RT-N10 C1 remotely, the settings were not reset to the factory settings.
If you do not see a menu on the left when entering the router settings via the web interface, it is sometimes treated by resetting the settings to the factory default with the reset button.
To reset the settings to the factory settings, you must press and hold the reset button until the power indicator flashes or goes out. Standard login and password – admin. The standard IP address is 192.168.1.1.
To restore the firmware, use the Firmware Restoration utility from the disk that comes with the router, you can also download it from the official site.
To start recovery you need:
1) Register the computer with a static IP address, for example, 192.168.1.2 with a subnet mask of 255.255.255.0, connect to one of the four LAN ports of the router.
2) Turn off the power of the router, press the reset button and hold it to turn on the power, the button must be held for about 15 seconds.
3) Run the Firmware Restoration utility, select the firmware file and load it into the router.
Is done.
The official page for downloading firmware and utilities for recovery – https://www.asus.com/support
Direct links:
https://www.asus.com/Networking/RTN10/HelpDesk_Download/
https://www.asus.com/Networking/RTN10_C1/HelpDesk_Download/
Asus Rt N10 Admin Password Reset
To update the firmware through the web interface, you need to open “Administration” – “Firmware Update”, select the new firmware file and click the “Submit” button. Wait until the operation is completed and in no case do not turn off the power of the router.
The new firmware must be necessarily under the version of the router, you can see it on the label under the router (for example, VER.B1, VER.С1, etc.). Flashing the wrong version can ruin the router.
On the test after flashing the RT-N10 C1 remotely, the settings were not reset to the factory settings.
If you do not see a menu on the left when entering the router settings via the web interface, it is sometimes treated by resetting the settings to the factory default with the reset button.
To reset the settings to the factory settings, you must press and hold the reset button until the power indicator flashes or goes out. Standard login and password – admin. The standard IP address is 192.168.1.1.
To restore the firmware, use the Firmware Restoration utility from the disk that comes with the router, you can also download it from the official site.
To start recovery you need:
1) Register the computer with a static IP address, for example, 192.168.1.2 with a subnet mask of 255.255.255.0, connect to one of the four LAN ports of the router.
2) Turn off the power of the router, press the reset button and hold it to turn on the power, the button must be held for about 15 seconds.
3) Run the Firmware Restoration utility, select the firmware file and load it into the router.
Is done.